Design and analysis of a PRRRP parallel mechanism for canopy vibration harvesting based on epitrochoid trajectory

Authors

  • Jun Pan 1. College of Optical, Mechanical and Electrical Engineering, Zhejiang A & F University, Hangzhou 311300, China;
  • Yuechan Li 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Puxiang Ma 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Xinjia Cui 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Xintao Han 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Chanda Mulongoti 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Hao Gao 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Hongli Chen 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China;
  • Liang Sun 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China; 3. Zhejiang Key Laboratory of Intelligent Sensing and Robotics for Agriculture, Hangzhou 310018, China
  • Zenghong Ma 1. College of Optical, Mechanical and Electrical Engineering, Zhejiang A & F University, Hangzhou 311300, China; 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China; 3. Zhejiang Key Laboratory of Intelligent Sensing and Robotics for Agriculture, Hangzhou 310018, China
  • Xiaoqiang Du 1. College of Optical, Mechanical and Electrical Engineering, Zhejiang A & F University, Hangzhou 311300, China; 2. School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China; 3. Zhejiang Key Laboratory of Intelligent Sensing and Robotics for Agriculture, Hangzhou 310018, China

Keywords:

Canopy vibration harvesting? Epitrochoid trajectory? Parallel mechanism? Camellia oleifera

Abstract

To address the persistent challenges of low harvesting efficiency and seasonal labor shortages in Camellia oleifera production, this study proposes a novel canopy vibration harvester driven by a five-bar PRRRP parallel mechanism configured to generate an epitrochoid excitation trajectory. Through analysis of the epitrochoid excitation trajectory and in accordance with parallel mechanism design principles, the PRRRP configuration was selected, considering structural layout, transmission system, motion performance, and singularity distribution. On this basis, a vibration harvesting device driven by the PRRRP mechanism was designed and developed. Kinematic and dynamic analyses, as well as workspace modeling, were conducted, and real-time position acquisition of the driving components was achieved through inverse kinematics solutions. The harvesting device includes dual servo motor-driven linear modules, articulated linkages, and an adjustable excitation frame fitted with excitation rods to engage the tree canopy. Using Camellia oleifera cultivar of Changlin No. 40 as the target crop, the device generated an epitrochoid trajectory with a vibration frequency of 7 Hz and an amplitude of 90 mm, delivering multidirectional excitation to the canopy. By adjusting tree size parameters, the vibration response of branches with different inclination angles was investigated. The results showed that average vibration response accelerations for branches inclined at 0°-30°, 30°-60°, and 60°-90° were 14.04 m/s2, 21.88 m/s2, and 21.27 m/s2, respectively, providing a theoretical basis for branch pruning. Harvesting trials indicated an overall fruit removal rate of 75.10% and an overall bud shedding rate of 11.55%, showing higher fruit removal and lower bud shedding than a traditional canopy vibration device employing linear reciprocating excitation. These results confirm that epitrochoid-based, parallel-mechanism excitation markedly improves fruit detachment efficiency and reduces collateral damage to tree architecture. Our study provides both theoretical insights and practical guidance for the development of next generation mechanized harvesters for Camellia oleifera and other woody fruit crops.      

Keywords: canopy vibration harvesting; epitrochoid trajectory; parallel mechanism; Camellia oleifera

DOI: 10.25165/j.ijabe.20261903.10206

Citation:  Pan J, Li Y C, Ma P X, Cui X J, Han X T, Mulongoti C, et al. Design and analysis of a PRRRP parallel mechanism for canopy vibration harvesting based on epitrochoid trajectory. Int J Agric & Biol Eng, 2026; 19(3): 159–171.

 

References

[1] Chen J P, Wang Y D, Zhou H P. Research on Camellia oleifera fruit harvesting machinery and sorting technology. Journal of Forestry Engineering, 2024; 9（4）: 12–24. （in Chinese）

[2] Whitney J, Wheaton T. Shakers affect Florida orange fruit yields and harvesting efficiency. Applied Engineering in Agriculture, 1987; 3（1）: 20–24.

[3] Aragon-Rodriguez F, Castro-Garcia S, Sola-Guirado R R, Gil-Ribes J A. Fruit abscission pattern of ‘Valencia’ orange with canopy shaker system. Scientia Horticulturae, 2019; 246: 916–920.

[4] Castro-Garcia S, Sola-Guirado R R, Gil-Ribes J A. Vibration analysis of the fruit detachment process in late-season ‘Valencia’orange with canopy shaker technology. Biosystems Engineering, 2018; 170: 130–137.

[5] Colmenero-Martinez J T, Blanco-Roldán G L, Bayano-Tejero S, Castillo-Ruiz F J, Sola-Guirado R R, Gil-Ribes J A. An automatic trunk-detection system for intensive olive harvesting with trunk shaker. Biosystems Engineering, 2018; 172: 92–101.

[6] Sola-Guirado R R, Aragon-Rodriguez F, Castro-Garcia S, Gil-Ribes J. The vibration behaviour of hedgerow olive trees in response to mechanical harvesting with straddle harvester. Biosystems Engineering, 2019; 184: 81–89.

[7] Dang K H, Niu Z J, Mu H T, Lan W K, Zhang X, Xin D, et al. Vibration harvesting process of olive trees based on response surface methodology and rigid-flexible coupling simulation. Int J Agric & Biol Eng, 2025; 18（3）: 25–36.

[8] Zhang W Q, Li Z Z, Tan Y Z, Li W. Optimal design and experiment on variable pacing combing brush picking device for Lycium barbarum. Transactions of the CSAM, 2018; 49（8）: 83–90. （in Chinese）

[9] Guo Y L, Bao Y D, He P Z, Wang H B. Design and experiment of hand-push lowbush blueberry picking machine. Transactions of the CSAE, 2012; 28（7）: 40–45. （in Chinese）

[10] Du X Q, Ning C, He L Y, Qian Y, Zhang G F, Yao X H. Design and test of crawler-type high clearance Camellia oleifera fruit vibratory harvester. Transactions of the CSAM, 2022; 53（7）: 113–121. （in Chinese）

[11] Homayouni T, Maharlooei M, Toudeshki A, Ferguson L, Ehsani R. Simultaneous trunk and canopy shaking improves table olive harvester efficiency versus trunk shaking alone. Horticulturae, 2023; 9（6）: 640.

[12] Pu Y J, Toudeshki A, Ehsani R, Yang F Z. Design and evaluation of a two-section canopy shaker with variable frequency for mechanical harvesting of citrus. Int J Agric & Biol Eng, 2018; 11（5）: 77–87.

[13] Zhuo P, Li Y, Wang B S, Jiao H B, Wang P, Li C S, Niu Q, Wang L H. Analysis and experimental study on vibration response characteristics of mechanical harvesting of jujube. Computers and Electronics in Agriculture, 2022; 203: 107446.

[14] Sola-Guirado R R, Sánchez-Cachinero P, Blanco-Roldán G. Simultaneous trunk and branch shaking in an over-the-row olive harvester. Biosystems Engineering, 2023; 231: 92–103.

[15] Rao H H, Hang D S, Wang Y L, Chen B, Liu M H. Design and experiment of hydraulic-driven Camellia fruit picking machine. Transactions of the CSAM, 2019; 50（5）: 133–139, 147. （in Chinese）

[16] Malladi A, Vashisth T, NeSmith S. Development and evaluation of a portable, handheld mechanical shaker to study fruit detachment in blueberry. HortScience, 2013; 48（3）: 394–397.

[17] Wu D L, Fu L Q, Cao C M, Li C, Xu Y P, Ding D. Design and experiment of shaking-branch fruit picking machine for Camellia fruit. Transactions of the CSAM, 2020; 51（11）: 176–182, 195. （in Chinese）

[18] Du X Q, Ni K N, Wu C Y. Vibratory harvesting mechanism for tree fruit based on epitrochoid. Transactions of the CSAM, 2016; 47（3）: 59–66. （in Chinese）

[19] Han M, Xiong B, Liu J, Yang D, Li T. Drive layout configuration strategy and scale optimization design of multi-drive mode parallel mechanism. Journal of Mechanisms and Robotics, 2024; 16（9）: 091002.

[20] Lin C S, Lee T. A classification method for input joints of planar five-bar mechanisms. Mechanism and Machine Theory, 2003; 38（11）: 1307–1322.

[21] Sun Y, Liu Y, Zou T, Jin M, Liu H. Design and optimization of a novel six-axis force/torque sensor for space robot. Measurement, 2015; 65: 135–148.

[22] Baron N, Philippides A, Rojas N. A novel kinematically redundant planar parallel robot manipulator with full rotatability. Journal of Mechanisms and Robotics, 2018; 11（1）: 011008.

[23] Wen K, Gosselin C M. Forward kinematic analysis of kinematically redundant hybrid parallel robots. Journal of Mechanisms and Robotics, 2020; 12（6）: 061008.

[24] Awad M I, Hussain I, Ghosh S, Zweiri Y, Gan D. A double-layered elbow exoskeleton interface with 3-PRR planar parallel mechanism for axis self-alignment. Journal of Mechanisms and Robotics, 2020; 13（1）: 011016.

[25] Du X Q, Han X T, Shen T F, Li S T, He L Y. Design and experiment of two-degree-of-freedom canopy shaking equipment based on 5R parallel mechanism. Transactions of the CSAM, 2023; 54（4）: 96–106. （in Chinese）

[26] Wang R Y, Fang D, Wu C, Wang B Y. Dynamic response of Camellia oleifera fruit-branch based on mathematical model and high-speed photography. Biosystems Engineering, 2024; 237: 232–241.

[27] Chen K Z. Design and research on canopy shaking harvester for Camellia oleifera fruit. MS thesis, Zhejiang Sci-Tech University, 2020. （in Chinese）. DOI: 10.27786/d.cnki.gzjlg.2020.000650.

Downloads

Published

2026-07-14

How to Cite

(1)
Pan, J.; Li, Y.; Ma, P.; Cui, X.; Han, X.; Mulongoti, C.; Gao, H.; Chen, H.; Sun, L.; Ma, Z. Design and Analysis of a PRRRP Parallel Mechanism for Canopy Vibration Harvesting Based on Epitrochoid Trajectory. Int J Agric & Biol Eng 2026, 19, 159–171.

Issue

Vol. 19 No. 3 (2026): IJABE

Section

Power and Machinery Systems

License

Copyright (c) 2026 International Journal of Agricultural and Biological Engineering

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

IJABE is an international peer reviewed, open access journal, adopting Creative Commons Copyright Notices as follows.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

Most read articles by the same author(s)